Products
The color is black
Soft, brushable creams for footwear with a pleasant soft and grabby touch, obtained from natural and synthetic waxes in water emulsion.
Their special formulation grants an easy, safe and quick application.
Apply by sponge on any type of finished leather and crust. The main characteristics of the VAL series of creams are excellent applicability, extreme softness and natural brightness.
These creams are particularly suitable for ironing.
Brushing by cotton brush with the DC 3800 abrasive wax enables the sealing of the leather treated with the VAL cream.
It can be applied as a first coat and then finished with the creams of the DC 4000/W series. The application of VAL creams in one or two coats is also highly appreciated and confers a soft and grabby touch.
The very fine emulsions of the waxes used in the VAL series confer to footwear a pleasantly soft and silky touch.
Its special formulation guarantees a easy, secure, fast application suitable for ironing.
The application of VAL by sponge in one or two coats, after brushing, grants leather with a natural gloss that exalts its attractiveness.
Fenice S.P.A heatable edge paint for excellent adhesion with any leather types edge.
You dont need wait 24 hours any more to work with edge, just try heatable edge paint from Fenice!
Fenice - thermopolymerizable base coat for mass production of leather goods. Viscosity index time is 40 seconds. The optimal temperature at the station is from 200 to 250 degrees, on the iron 170-220 degrees. Attention! Vulcanization of paint is not allowed!
Thermopolymerizable base coat can also be dried in a drying chamber at a temperature of 50 ° C or on a table at room temperature.
Fenice is a company with more than 40 years of experience working with global brands.
General rules for applying edge paints:
Prepare a clean leather edge.
Then apply a coat of Fenice HS 5750/TC edge paint primer and let dry for 10-20 minutes. Do not apply too much primer in one iteration.
Next, apply a layer of edge paint and allow to dry for 10-20 minutes (drying time depends on the temperature and humidity level in the room). Don't apply too much paint in one iteration.
When the paint is dry, you can sand it with 240 to 1000 grit sandpaper to achieve an even surface. You can also use a filleteuse hot iron to flatten the edge.
Clean the edge surface with a damp cloth
Repeat steps 3, 4 and 5 until you get the desired result.
Finishing options:
Matte - Leave the last coat of paint as it is.
Semi Gloss - Apply Columbus Edge Wax you can smooth it with a canvas cloth or hot iron or filleteuse.
This is the weight you need for a Beautiful Edge.
Product Features
It is a cream used in the final cleaning stage in finishing.
Application
As a final process, it is applied with a sponge in a thin layer. After drying for a short time (5-10 min.), it is polished with a low speed brush and a vivid appearance is obtained.
Product Features
It is a cream used in the final cleaning stage in finishing.
Application
As a final process, it is applied with a sponge in a thin layer. After drying for a short time (5-10 min.), it is polished with a low speed brush and a vivid appearance is obtained.
Shoe Cream P/1-S
This high gloss product is a cream for finishing leather shoes or any leather product (except suede).
Application: To balance the colour where necessary or to give the leather an antique effect.
Colours: ✔ Natural ✔ Coloured
Shoe Cream P/1
It is a cream used for finishing leather shoes or any leather product (except suede). It brings out all the characteristics of the leather and gives it a unique shine and softness. It can also be used to highlight the colour and give an aged look.
Application: Apply with a sponge or cloth. After a short time, apply by hand with a rotating brush or a medium speed woollen cloth or woollen cloth.
Colours: ✔ Natural ✔ Coloured
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Rimtex ™ 020 is a soft effect non-woven based leather reinforcement material. Its highly elastic and stretchable structure lets it to be used in virtually all areas where reinforcement is needed.
Rimtex ™ 020 has high elasticity, easy forming properties, high air permeability and lower cost compared to cotton based materials.
Rimtex ™ 020 can be applied on the whole upper, cheeks or side walls of boots and shoes.
The special low activation temperature of 90°C coating lets it to be used with real and vinyl type leathers.
Application temperature: 90°C - 120°C 5-10 seconds
Supplied as minimum of 100 meter rolls.
Rimtex ™ 040 is a soft effect non-woven based leather reinforcement material. Its highly elastic and stretchable structure lets it to be used in virtually all areas where reinforcement is needed.
Rimtex ™ 040 has high elasticity, easy forming properties, high air permeability and lower cost compared to cotton based materials.
Rimtex ™ 040 can be applied on the whole upper, cheeks or side walls of boots and shoes.
The special low activation temperature of 90°C coating lets it to be used with real and vinyl type leathers.
Application temperature: 90°C - 120°C 5-10 seconds
Supplied as minimum of 100 meter rolls.
Rimtex ™ 070 is a soft effect non-woven based leather reinforcement material. Its highly flexible but non-stretchable structure lets it to be used in virtually all areas where strong reinforcement is needed.
Rimtex ™ 070 has high flexibility, easy forming properties and lower cost compared to cotton based materials.
Rimtex ™ 070 can be applied on the whole upper, cheeks or side walls of boots and shoes.
The special low activation temperature of 90°C coating lets it to be used with real and vinyl type leathers.
Application temperature: 90°C - 120°C 5-10 seconds
Supplied as minimum of 100 meter rolls.
Rimtex ™ 090 is a soft effect non-woven based leather reinforcement material. Its highly flexible but non-stretchable structure lets it to be used in virtually all areas where strong reinforcement is needed.
Rimtex ™ 090 has high flexibility, easy forming properties and lower cost compared to cotton based materials.
Rimtex ™ 090 can be applied on the whole upper, cheeks or side walls of boots and shoes.
The special low activation temperature of 90°C coating lets it to be used with real and vinyl type leathers.
Application temperature: 90°C - 120°C 5-10 seconds
Supplied as minimum of 100 meter rolls.
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Solvent Aktif ™ is a rigid counter material produced through polyester fabric impregnation in PS based resins. Solvent Aktif ™ must be dipped in suitable solvents for activation of the PS structure. This processing allows to get adhesion and lasting properties depending on the dipping time. It shows higher elasticity and flexural modulus after drying.
Solvent Aktif ™ is especially suitable for high quality ladies and man shoes.
Lotus 40 is a semi-rigid non-woven based leather reinforcement material. Its strong structure lets it to be used in virtually all areas where reinforcement is needed.
Lotus 40 has a verycompetitive price againts its cotton counterparts.
It has a stiffer effect compared to Rimtex ™ series of products and used as both reinforcement and ping pong effect toe puff and counters in soft ladies shoes.
Lotus has easy forming and good form retention properties, high air permeability.
The special low activation temperature of 90°C coating lets it to be used with real and vinyl type leathers.
Application temperature: 90°C - 120°C 5-10 seconds
Supplied as minimum of 100 meter rolls
FIRMNESS: MEDIUM
THICKNESS: 0.60 – 1.35 mm (± 0.05 mm)
· Material with polyurethane adhesive on one or two sides available in hydrofire.
· Excellent adherence on all materials. gives the toe a special softness and flexibility.
· Complies with GRS certification containing up to 60% of recycled raw material.
Designed for machine mounting, Infinity® Thermoplastic counter, which is the choice of shoe manufacturers working with automation, is preferred for quality boots and shoes. Both sides, top and bottom, are coated with thermoplastic adhesive for toe puff use. The model, which is coated on one side as counter material, has "S" in the code.
Available from 0.6 mm to 1.8 mm.
Inf 1050 0,6 mm
Inf 128 0,8 mm
Inf 130 1,0 mm
Inf 145 1,2 mm
Inf 236 1,4 mm
Inf 272 1,6 mm
Inf 284 1,8 mm
The first choice of mass production footwear manufacturers, thermoplastic Optimum® fort products, designed for machine assembly, are designed to reduce your production costs without compromising on the name. The right choice for mass-produced shoes and boots.
Perfect form, cost effective.
Available from 0,8 mm to 1,4 mm.
